HMC784 TR SWITCH or RF SPDT switch 10 Watts max, 15-40 nsec 60 dBm IMD3 8V CMOS

Description

<div style="text-align:center"><img src="http://ti2.auctiva.com/sw/java.gif" border="0"><br><table align="center"><tbody><tr><td><a style="text-decoration:none" href="http://store.auctiva.com/gr_makis"><img src="http://ti2.auctiva.com/sw/images.gif" border="0"></a></td><td height="27px" valign="middle" align="center"><font face="arial" size="2"><b><a href="http://store.auctiva.com/gr_makis">gr_makis</a> Store</b></font></td></tr></tbody></table></div>
ATTENTION:
The price shown
includes Greek VAT 24%
and is applicable to
all individuals in EU countries only
.
If you are from any other country including USA, Canada, Australia etc. please use the "make offer" button and divide the price by 1,24.
We will first accept this offer to let you proceed with the check-out and payment.
If you are a business registered in EU with a valid VAT number again, you can use the same button so to pay without VAT. We will send you a zero VAT tax invoice.
HMC784 - 10W RF
SPDT Switch
LF to 4000 MHZ (4 GHZ), 30 dB Isolation,
15-40 nSec switching times
Very Low DC current - Good IMD3  (+60 dBm)
Based on the Hittite (now Analog Devices) HMC784 GaAs MMIC, this small PCB module is a complete RF SPDT (Single Pole Dual Toggle) Switch for 50 ohm systems
working from below 1 MHZ to more than 4000 MHZ with very low distortion at high power signal levels, up to + 40dBm (10 Watts), high transition speed and good isolation.
It has an RF input port and two output ports. Which output port is ON, is selected by a simple 2-bit interface and the port which is selected as OFF, becomes reflective short.
It draws under 20 uA at 8 VDC recommended for best transition speed, isolation and power handling, while still works from 3V DC with 0.5 uA current draw but with less isolation and power handling
.
​
The PCB dimensions are only 33 x 38.5 mm and SMA edge connectors are used for all RF ports.
J4 is a 5-pin header and it is used to control the switch with its pin 1. It has a pull-up resistor (R3) and as is, the input port connects to the output J3. Applying a LOW at pin 1 the input port connects to J2 output port. Pin 5 is the Vdd input, 3 to 8 Volts will work, but for optimum results one should use 8V. Pins 2,3 and 4 are connected to the ground.
The 3 DC blocking capacitors are missing from the PCB module so they can be selected upon the application frequency range.
Also, in order not to distort the transmission line which connects J1 to the MMIC, a small wire link should be added to power the chip with DC power. It is shown at the middle photo below.
See more info at www.sv1afn.com under projects
ORDERS For a complete DIY KIT  USD 42.26 incl 24% VAT
If you have a valid EU VAT number please email us for an invoice with VAT exception.
The KIT includes a  high-quality ENIG FR4 PCB (33 x 38.5 mm) that comes with all SMD components pre-soldered except the DC blocking capacitors C1, C2 and C3 (0402 or 0603 size).
You need to solder one small wire on the bottom side of the PCB.
Three SMA female connectors with nuts and washers for pcb edge mounting are also supplied, unsoldered.
The shipping is with registered mail  (your signature is required upon delivery).
I usually ship the next day and it takes about a week to 10 days for USA or Australia, less than a week for Europe.​
Check out my
other items
! I always combine shipping.