NEW MR300 Digital Shortwave Antenna Analyzer Meter Tester 1-60M For Ham Radio

Description

Feature :
Note : the item  is not inclued  Built-in battery,Does not support Bluetooth
Radio enthusiasts an essential tool for entry
Test the antenna technical parameters
Can test the standing wave, impedance, capacitance and so on
Can be connected to the computer to do antenna and other graphic analysis
Test frequency: 1-60M
Size: 90mm * 82mm * 30mm
Connector: M head
Power requirements: within the positive external
12V - Driveable talent works, but can not charge the battery.
13.8V ~ 18V - can drive the talent to work normally, can also be normal for the battery charge.
Specifications
1 Frequency Generation & Control:
o 1 - 60 Mhz
o Source impedance: 50 Ohms
o Stability: +/- 100 ppm
o Spectral Purity: Harmonics down >- TBD dB beyond 60 MHz
o Step Size: User configurable increments of 100 Hz, 1 kHz, 10 kHz, and 100 kHz
Usable Measurement Range:
o  SWR: 1.0 to 9.99
o Impedance: approx. 5 to 2000 ohms
RF Output:
o Adjustable: 2.0 Volts pp (typ)
? Power supply:
o External: 13.8 to 19 Volts DC, 500mA
o Internal: 8xAAA 1000mAh NiMH cells
o Charging time: 12 hours (charge rate 0.1C)
2 Controls:
o Pushbuttons (5): "Mode", "Band", "Config", "Scan", "Up", "Down"
o Switch: "Power On"
? Connectors:
o RF Out: BNC
o USB: Mini-B receptacle
o External power: 2.1mm Power Jack (center pin positive)
3 Instrument Capabilities:
o Measure antenna electrical parameters: SWR, impedance (resistance +
reactance), capacitance, inductance
o Measure feedpoint impedance
o Measure ground loss
Adjust antenna tuners and determine loss
o Measure inductors and capacitors
o Measure coax transmission line (SWR, length, velocity factor, approximate Q
and loss, resonant frequency, and impedance)
o Measure and determine optimum settings for tuning stubs: SWR, approximate
Q, resonant frequency, bandwidth, impedance
o Determine characteristic impedance of transmission line
o Determine length of ¼ and ½ wave phasing lines
o Coaxial Cable Loss
o Determine antenna tuner loss
o Measure balun loss
o Measure inductor Q
o Estimate quartz crystal parameters
Adjust antenna tuners and determine loss
o Measure inductors and capacitors
o Measure coax transmission line (SWR, length, velocity factor, approximate Q
and loss, resonant frequency, and impedance)
o Measure and determine optimum settings for tuning stubs: SWR, approximate
Q, resonant frequency, bandwidth, impedance
o Determine characteristic impedance of transmission line
o Determine length of ¼ and ½ wave phasing lines
o Coaxial Cable Loss
o Determine antenna tuner loss
o Measure balun loss
o Measure inductor Q
o Estimate quartz crystal parameters
Adjust antenna tuners and determine loss
o Measure inductors and capacitors
o Measure coax transmission line (SWR, length, velocity factor, approximate Q
and loss, resonant frequency, and impedance)
o Measure and determine optimum settings for tuning stubs: SWR, approximate
Q, resonant frequency, bandwidth, impedance
o Determine characteristic impedance of transmission line
o Determine length of ¼ and ½ wave phasing lines
o Coaxial Cable Loss
o Determine antenna tuner loss
o Measure balun loss
o Measure inductor Q
o Estimate quartz crystal parameters
package :
1pc NEW MR300 Digital Shortwave Antenna Analyzer Meter Tester 1-60M For Ham Radio
sent manual by email